Shop
- All products
- 3D Printer64 products
- Books0 products
- Devices3 products
- Electrical71 products
- Our Products1 product
- OUR ROBOTS2 products
- Power Supply8 products
- Sensor23 products
- SERVICES PROVIDED2 products
- TOBOIDS auto0 products
- TOBOIDS AUTOMATA0 products
- Electronics60 products
- Mechanical31 products
- Lighting4 products
1 Channel 12V 30A Relay Control Board Module with Optocoupler
The inputs of 1 Channel 12V 30A Relay Module are isolated to protect any delicate control circuitry.It can be used as a single chip module for appliance control and work with both DC or AC signals where you can control the 220V AC load.
1.5mm Series AMP Superseal Waterproof Female Connector (Housing + Wire seal + Female Terminal)
AMP Superseal 1.5 series connector family to meet the increasing requirements for reliability in waterproof applications. The AMP Superseal 1.5 series connector exceeds the requirements prescribed by IP67 according IEC 60529 and DIN 40050-9 standards and has its application in automotive, agriculture, and industrial machinery. The AMP SUPERSEAL 1.5 series connector system is qualified for sensor applications as well.
1.5mm Series AMP Superseal Waterproof Male Connector (Housing + Wire seal + Male Terminal)
AMP Superseal 1.5 series connector family to meet the increasing requirements for reliability in waterproof applications. The AMP Superseal 1.5 series connector exceeds the requirements prescribed by IP67 according IEC 60529 and DIN 40050-9 standards and has its application in automotive, agriculture, and industrial machinery. The AMP SUPERSEAL 1.5 series connector system is qualified for sensor applications as well.
1.5V 1.8V 2.5V 3V 3.3V 3.7V 4.2V to 5V DC-DC Boost Converter Step-Up Module
This voltage boost converter module provides 5V DC stable voltage output at various input ranges between 1.5V to 5V and boosts the voltage level providing an amplified stabilized 5V output. For different input ranges, it consumes different amount of current to produce a balanced output.
10K ohm potentiometer, single variable resistor (Round)
OVERVIEW
Resistance Value of 10K Ohms Adjustable Rotary Control Three-Terminal Configuration Precision Tuning Compact Size & High Durability
10M GT2 Width 6mm White Open Timing Belt For 3D Printer
OVERVIEW
- Pitch: 2mm
- Material: Neoprene Rubber With Fiberglass Core
- Width: 6mm
- Total Length: 10M
- Shape: Open Loop
- Core Wire Material: Glass Fiber
10×4.5 inch -Propeller Pair for Quadcopter (Nylon Black)
Specifications of 10x4.5 inch Propeller Pair
Diameter: 10" (25.4 cm) Pitch: 4.5" (11.43 cm) Material: Nylon Includes one CW rotating propeller and one CCW rotating propeller
12 Volt DC Motor – 200 RPM
OVERVIEW
- Gear Material: Plastic
- Rated RPM: 500
- Operating Voltage(VDC): 12
- Rated Torque(kg-cm): 0.7
- Stall Torque(Kg-Cm): 3
- Load Current(A): 0.3
- No-Load Current: 60mA
- Gearbox Diameter (mm): 37
- Motor Diameter(mm): 32
- Motor Length(mm): 75
- Shaft Diameter (mm): 6
- Shaft Length (mm): 22
- Weight (gm): 80
12V 300mA Power Supply Module
This is a 12V Power Supply Module which can provide a current of 300mA to drive the LED strip. The module is small in size so that it can be easily integrated into any system if necessary and has a maximum power output of 5W.
12v-24v to 5V 3A Super Mini Super Size DC Step-Down Module With 97.5% Efficiency.
This Super Mini Super Size DC Step-Down Module uses an integrally molded power inductor and synchronous rectifier control chip which is smaller, efficient and can be used as a DIY mobile power, monitor power supply, power buggies, camera power supply, car power, communications equipment supply, various right size and weight for demanding applications.
150 RPM BO Motor- L Shape
OVERVIEW
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): (Double D-type) 5.5
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 150
- Rated Torque: 0.8 kg-cm
- Weight (gm): 30
- Dimensions in mm (LxWxH): 42 x 55 x 22
- Gearbox Shape: L-Shape
150 RPM Single Shaft BO Motor – Straight
OVERVIEW
- Cost-effectiveness of the injection-molding process.
- Elimination of machining operations.
- Low density: lightweight, low inertia.
- Uniformity of parts.
