Back to products
Electrical
- All products
- 3D Printer64 products
- Books0 products
- Devices3 products
- Electrical71 products
- Our Products1 product
- OUR ROBOTS4 products
- Power Supply8 products
- Sensor23 products
- SERVICES PROVIDED2 products
- TOBOIDS auto0 products
- TOBOIDS AUTOMATA0 products
- Electronics61 products
- Mechanical31 products
- Lighting4 products
360 degree Rotary encoder | D shape shaft handle | 100K Resistance Value
OVERVIEW
Type: 360° Rotary Encoder Resistance Value: 100K ohms Power Rating: 1W Shaft: 7 mm D-shaped shaft Maximum Input Voltage: 200 VDC Rotational Life: 2,000,000 cycles
3V Miniature DC Motor
OVERVIEW
- Operating Voltage: 3V to 6V
- No-load current: 350mA
- RPM: 150 rpm.
- Axial Length: 9mm
- Shaft Diameter: 2mm
4 Bit Independent Keypad Button Module
4 bit independent keypad button module is designed for Arduino or other hobby kits and can be easily assembled or inserted in any project or prototype due to its small size.
5-Channel Flame Sensor Module
5-Channel Flame Sensor Module is a 5 channel flame detector module is used to detect flame in the larger area allowing flame detection with 5 flame sensors which are arranged at 30 degrees between them and can output an analog signal which would be more precise and also a digital signal which would be more easy to use, you can adjust the digital output sensitivity by the onboard potentiometer.
5V 0.2A 3007 Cooling Fan for Raspberry Pi and 3D Printer
OVERVIEW
- Perfectly fit on the extruder
- Noiseless Performance
- Very low Current consumption
- Easy to install and connect.
60 RPM BO Motor – Straight
OVERVIEW
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): (Double D-type) 5.5
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 60
- Rated Torque: 1 kg-cm
- Weight (gm): 30
- Dimensions in mm (LxWxH): 62x28x20
80A brushless speed controller
OVERVIEW
Current Rating: 80A continuous current. Burst Current: 100A BEC:5A/5V Voltage Range: Compatible with 2-6S LiPo batteries. Throttle signal refresh rate (Hz): 50 ~ 432.
9v battery clip connector
OVERVIEW
- Excellent material, fine workmanship.
- Wire Length: approx 10cm.
- Colour: Blue, Black
- Avoid the polarity conflict and short circuit.
A3967 Stepper Motor Driver For Arduino
A3967 Stepper Motor Driver For Arduino provides greater flexibility and control over stepper motor and is compatible with most microcontrollers that can output a digital 0 to 5V pulse(0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver).It can operate bipolar stepper motors in full-, half-, quarter-, and eighth-step modes, with output drive capability of 30 V and ±750 mA.
A4988 Stepper Motor Driver Controller Board
OVERVIEW
- Suggested Match: 3A004
- Color: Red
- Material: Metal + PCB Board
- Dimensions (mm): 41x 34x 11
- Weight (gm): 10
A4988 Stepper Motor Driver Module
The A4988 driver Stepper Motor Driver is a complete micro-stepping motor driver which operates from 8 V to 35 V and can deliver up to approximately 1A per phase without a heat sink and 2A per phase with a heat sink.. It is designed to operate bipolar stepper motors in full-step, half-step, quarter-step, eighth-step and sixteenth-step modes.
A88 Metal Detector Non-Contact Metal Induction Detection Module
A88 Metal detector non-contact metal induction detection module makes a sound when it approaches any metal which operates by inducing currents in metal objects and responding when it occurs.The power cables of the Metal detector non-contact metal induction detection module will need soldering on for the module to function, positive to the outside of the module and negative between the potentiometer and an electrolytic capacitor.
